Artículo: AMZ-B0DSHKDG9C

MakerFocus

MakerFocus 5pcs 1.3 Inch I2C IIC OLED Display Module 128 x 64 Pixel SH1106 Self-Luminous Display Board for Arduino/Raspberry Pi/ESP32 (Pre-Soldered, White)

Size:

Detalles del producto

Disponibilidad
En stock

Peso con empaque
0.20 kg

Devolución
Sí

Condición
Nuevo

Producto de
Amazon

Viaja desde
USA

Sobre este producto

1.3-inch I2C IIC OLED display module is a mini display screen with 128 x 64 resolution and SHH1106 chipset Standard IIC communication interface pinout and these modules can be controlled by I2C, compatible with most platform such as Arduino, Raspberry Pi, ESP, etc Features: Easy to setup Super low power consumption Support I2C IIC communication Protocol Good compatibility: for Arduino, ESP32, C51, MSP430 series, STM32, Raspberry Pi 5/4B/3B+/3B/2B/Zero and so on Parameters: Driver Chip:SH1106 Resolution: 128*64 Colour: White Viewing Angle: >160° Power Consumption: 0.06W Wide Voltage Support: 3.3V or 5V DC Working Temperature: -20℃-60℃ Communication Mode: IIC, only 2 I/O interfaces are required OLED self-luminous, no backlight required Use mould taking software to take characters Pin Definition: GND: Ground VCC: 3.3V-5V SCL: Serial Clock SDA: Serial Data Size: Screen Size: 1.3 inch Effective Display Area (AA area): 29.42x14.7mm PCB Backplane Size: 33.50x35.40mm Package Content: 5 * 1.3-inch IIC I2C OLED Display Module

$44,39

49% OFF

$22,77

$44,39

49% OFF

$22,77

Envío gratis

Llega en 5 a 12 días hábiles

Con envío

Tienes garantia de entrega

Medios de pago

Cantidad

Este producto viaja de USA

a tus manos en

Medios de pago

Conoce más detalles

128 x 64 Pixel: Needn't backlight, these OLED module can self-luminous. It has super high contrast, bright and crisp dots, viewing angle is greater than 160°, even tiny fonts quite readable No Embedded Fonts: There are no embedded fonts inside these Arduino display module, you can create the fonts through font generation software Changeable IIC Address: Solder the resistor to the 0x78 side on the back and disconnect the 0x7A side, then the 0x78 slave device address will be selected (default); Solder the resistor on the 0x7A side and disconnect the 0x78 side, then the 0x7A slave device address will be selected; when switches the IIC slave address of the hardware, the software should be modified accordingly Application: These OLED display can be used for Arduino, Raspberry Pi 5/4B/3B+/3B/2B/Zero, STM32, C51, MSP430, ESP32 development board and so on. Showing graphical & textual information directly of your machines Parameters: Screen Size: 1.3-inch; Driver Chip:SH1106; Resolution: 128*64; Color: White; Viewing Angle: >160°; Power Consumption: 0.06W; Voltage: 3.3V or 5V DC; Working Temperature: -20℃-60℃

MakerFocus 5pcs 1.3 Inch I2C IIC OLED Display Module 128 x 64 Pixel SH1106 Self-Luminous Display Board for Arduino/Raspberry Pi/ESP32 (Pre-Soldered, White)

Conoce más detalles

MakerFocus 2pcs 0.91 Inch I2C IIC OLED Display Module 128 x 32 Pixel SSD1306 Driver Self-Luminous Display Board for Arduino/Raspberry Pi/ESP32 (White)

MakerFocus 2pcs 1.3 Inch I2C IIC OLED Display Module 128 x 64 Pixel SH1106 Self-Luminous Display Board for Arduino/Raspberry Pi/ESP32

MakerFocus 5pcs 0.91 Inch I2C IIC OLED Display Module 128 x 32 Pixel SSD1306 Driver Self-Luminous Display Board for Arduino/Raspberry Pi/ESP32 (Pre-Soldered, White)

MakerFocus 4pcs 0.91 Inch I2C IIC OLED Display Module 128 x 32 Pixel SSD1306 Driver Self-Luminous Display Board for Arduino/Raspberry Pi/ESP32 (White)

MakerFocus 2pcs ESP32 LoRa V3 Development Board with 915 MHz Antenna Integrated WiFi Bluetooth SX1262 CP2102 0.96-inch OLED Display Type C Interface for Meshtastic IoT Arduino Intelligent Scenes

MakerFocus ESP32 LoRa V3 Development Board with 3000mAh Battery and 915MHz Antenna, Integrated WiFi Bluetooth SX1262 CP2102 0.96-inch OLED Display Type C for Meshtastic IoT Arduino Intelligent Scene

MakerFocus 2pcs ESP32 LoRa V3 Development Board with 2pcs 3000mAh Battery, 915MHz Antenna Integrated WiFi Bluetooth SX1262 CP2102 0.96-inch OLED Display for Meshtastic IoT Arduino Intelligent Scene

MakerFocus ESP32 OLED WiFi Kit V3 Integrated WiFi Bluetooth CP2102 IoT Development Board with 0.96-inch OLED Display for Arduino Intelligent Scenes

MakerFocus 2 Set ESP32 LoRa V3 Development Board with 915 MHz Antenna and Case Integrated WiFi Bluetooth SX1262 CP2102 0.96-inch OLED Display Type C for Meshtastic IoT Arduino Intelligent Scenes

MakerFocus Wireless Tracker Supports GPS Galileo Multi-System Joint Positioning ESP32-S3 WiFi Bluetooth SX1262 UC6580 with 3000mAh Battery, 915MHz LoRa Antenna, 0.96-inch LCD Display for Meshtastic

MakerFocus ESP32 LoRa V3 Development Board with 2000mAh Battery and 915MHz Antenna, Integrated WiFi Bluetooth SX1262 CP2102 0.96-inch OLED Display Type C for Meshtastic IoT Arduino Intelligent Scene

MakerFocus ESP32 LoRa V3 Development Board with 3000mAh Battery and 915MHz Antenna, Integrated WiFi Bluetooth SX1262 CP2102 0.96-inch OLED Display Type C for Meshtastic IoT Arduino Intelligent Scene

MakerFocus 2pcs ESP32 LoRa V3 Development Board with 2pcs 3000mAh Battery, 915MHz Antenna Integrated WiFi Bluetooth SX1262 CP2102 0.96-inch OLED Display for Meshtastic IoT Arduino Intelligent Scene

MakerFocus 2pcs 0.91 Inch I2C IIC OLED Display Module 128 x 32 Pixel SSD1306 Driver Self-Luminous Display Board for Arduino/Raspberry Pi/ESP32 (White)

MakerFocus 2pcs ESP32 LoRa V3 Development Board with 915 MHz Antenna Integrated WiFi Bluetooth SX1262 CP2102 0.96-inch OLED Display Type C Interface for Meshtastic IoT Arduino Intelligent Scenes

MakerFocus 4pcs 3.7V Lithium Rechargeable Battery JST1.25 Connector 2pin, 952540 3.7V 1000mAh Battery with Protection Board and Insulated Rubber Tape Compatible with ESP32 Development Board

MakerFocus 4pcs 3D Printer Fan 12V, 40mm 12 Volt 0.08A DC Mini Quiet Cooling 40 x 40 x10mm with 28cm Cable for 3D Printer, DVR and Other Small Appliances Series Repair Replacement

MakerFocus 15pcs TP4056 Charging Module Type C Interface with Battery Protection 18650 BMS 5V 1A 18650 Lithium Battery Charging Board

MakerFocus TF-Luna LiDAR Range Finder Sensor Module, Single-Point Micro Ranging Module 0.2 to 8m Compatible with Pixhawk, Arduino and Raspberry Pi with UART / I2C Communication Interface

MakerFocus 5pcs 0.91 Inch I2C IIC OLED Display Module 128 x 32 Pixel SSD1306 Driver Self-Luminous Display Board for Arduino/Raspberry Pi/ESP32 (Pre-Soldered, White)

MakerFocus 2 Set ESP32 LoRa V3 Development Board with 915 MHz Antenna and Case Integrated WiFi Bluetooth SX1262 CP2102 0.96-inch OLED Display Type C for Meshtastic IoT Arduino Intelligent Scenes

MakerFocus 2pcs 1.3 Inch I2C IIC OLED Display Module 128 x 64 Pixel SH1106 Self-Luminous Display Board for Arduino/Raspberry Pi/ESP32

MakerFocus 4pcs 0.91 Inch I2C IIC OLED Display Module 128 x 32 Pixel SSD1306 Driver Self-Luminous Display Board for Arduino/Raspberry Pi/ESP32 (White)

Información útil

Centro de ayuda

Todo en un solo lugar

Comprá con tranquilidad

MakerFocus 5pcs 1.3 Inch I2C IIC OLED Display Module 128 x 64 Pixel SH1106 Self-Luminous Display Board for Arduino/Raspberry Pi/ESP32 (Pre-Soldered, White)

Conoce más detalles

Productos Relacionados

MakerFocus 2pcs 0.91 Inch I2C IIC OLED Display Module 128 x 32 Pixel SSD1306 Driver Self-Luminous Display Board for Arduino/Raspberry Pi/ESP32 (White)

MakerFocus 2pcs 1.3 Inch I2C IIC OLED Display Module 128 x 64 Pixel SH1106 Self-Luminous Display Board for Arduino/Raspberry Pi/ESP32

MakerFocus 5pcs 0.91 Inch I2C IIC OLED Display Module 128 x 32 Pixel SSD1306 Driver Self-Luminous Display Board for Arduino/Raspberry Pi/ESP32 (Pre-Soldered, White)

MakerFocus 4pcs 0.91 Inch I2C IIC OLED Display Module 128 x 32 Pixel SSD1306 Driver Self-Luminous Display Board for Arduino/Raspberry Pi/ESP32 (White)

MakerFocus 2pcs ESP32 LoRa V3 Development Board with 915 MHz Antenna Integrated WiFi Bluetooth SX1262 CP2102 0.96-inch OLED Display Type C Interface for Meshtastic IoT Arduino Intelligent Scenes

MakerFocus ESP32 LoRa V3 Development Board with 3000mAh Battery and 915MHz Antenna, Integrated WiFi Bluetooth SX1262 CP2102 0.96-inch OLED Display Type C for Meshtastic IoT Arduino Intelligent Scene

MakerFocus 2pcs ESP32 LoRa V3 Development Board with 2pcs 3000mAh Battery, 915MHz Antenna Integrated WiFi Bluetooth SX1262 CP2102 0.96-inch OLED Display for Meshtastic IoT Arduino Intelligent Scene

MakerFocus ESP32 OLED WiFi Kit V3 Integrated WiFi Bluetooth CP2102 IoT Development Board with 0.96-inch OLED Display for Arduino Intelligent Scenes

MakerFocus 2 Set ESP32 LoRa V3 Development Board with 915 MHz Antenna and Case Integrated WiFi Bluetooth SX1262 CP2102 0.96-inch OLED Display Type C for Meshtastic IoT Arduino Intelligent Scenes

MakerFocus Wireless Tracker Supports GPS Galileo Multi-System Joint Positioning ESP32-S3 WiFi Bluetooth SX1262 UC6580 with 3000mAh Battery, 915MHz LoRa Antenna, 0.96-inch LCD Display for Meshtastic

MakerFocus ESP32 LoRa V3 Development Board with 2000mAh Battery and 915MHz Antenna, Integrated WiFi Bluetooth SX1262 CP2102 0.96-inch OLED Display Type C for Meshtastic IoT Arduino Intelligent Scene

Otros Productos

MakerFocus ESP32 LoRa V3 Development Board with 3000mAh Battery and 915MHz Antenna, Integrated WiFi Bluetooth SX1262 CP2102 0.96-inch OLED Display Type C for Meshtastic IoT Arduino Intelligent Scene

MakerFocus 2pcs ESP32 LoRa V3 Development Board with 2pcs 3000mAh Battery, 915MHz Antenna Integrated WiFi Bluetooth SX1262 CP2102 0.96-inch OLED Display for Meshtastic IoT Arduino Intelligent Scene

MakerFocus 2pcs 0.91 Inch I2C IIC OLED Display Module 128 x 32 Pixel SSD1306 Driver Self-Luminous Display Board for Arduino/Raspberry Pi/ESP32 (White)

MakerFocus 2pcs ESP32 LoRa V3 Development Board with 915 MHz Antenna Integrated WiFi Bluetooth SX1262 CP2102 0.96-inch OLED Display Type C Interface for Meshtastic IoT Arduino Intelligent Scenes

MakerFocus 4pcs 3.7V Lithium Rechargeable Battery JST1.25 Connector 2pin, 952540 3.7V 1000mAh Battery with Protection Board and Insulated Rubber Tape Compatible with ESP32 Development Board

MakerFocus 4pcs 3D Printer Fan 12V, 40mm 12 Volt 0.08A DC Mini Quiet Cooling 40 x 40 x10mm with 28cm Cable for 3D Printer, DVR and Other Small Appliances Series Repair Replacement

MakerFocus 15pcs TP4056 Charging Module Type C Interface with Battery Protection 18650 BMS 5V 1A 18650 Lithium Battery Charging Board

MakerFocus TF-Luna LiDAR Range Finder Sensor Module, Single-Point Micro Ranging Module 0.2 to 8m Compatible with Pixhawk, Arduino and Raspberry Pi with UART / I2C Communication Interface

MakerFocus 5pcs 0.91 Inch I2C IIC OLED Display Module 128 x 32 Pixel SSD1306 Driver Self-Luminous Display Board for Arduino/Raspberry Pi/ESP32 (Pre-Soldered, White)

MakerFocus 2 Set ESP32 LoRa V3 Development Board with 915 MHz Antenna and Case Integrated WiFi Bluetooth SX1262 CP2102 0.96-inch OLED Display Type C for Meshtastic IoT Arduino Intelligent Scenes

MakerFocus 2pcs 1.3 Inch I2C IIC OLED Display Module 128 x 64 Pixel SH1106 Self-Luminous Display Board for Arduino/Raspberry Pi/ESP32

MakerFocus 4pcs 0.91 Inch I2C IIC OLED Display Module 128 x 32 Pixel SSD1306 Driver Self-Luminous Display Board for Arduino/Raspberry Pi/ESP32 (White)

Compra protegida

¿Cómo comprar?

Información de Aduanas Ecuador

Garantía de entrega

¿Cómo solicitar una devolución?

Los productos sin devolución son:

Tarjetas de Débito y Crédito

Pagos a través de PayPal

¿Cómo comprar?

Hacemos todo por ti

Tarjetas de Débito, Crédito y Deuna

Pagos a través de Deuna

Pagos a través de PayPal

Garantía de entrega

Compra como si vivieras fuera, pero desde cualquier lugar de Ecuador